Alloy wheel

In the automotive industry, alloy wheels are wheels that are made from an alloy of aluminium or magnesium. Alloys are mixtures of a metal and other elements. They generally provide greater strength over pure metals, which are usually much softer and more ductile. Alloys of aluminium or magnesium are typically lighter for the same strength, provide better heat conduction, and often produce improved cosmetic appearance over steel wheels. Although steel, the most common material used in wheel production, is an alloy of iron and carbon, the term “alloy wheel” is usually reserved for wheels made from nonferrous alloys.

The earliest light-alloy wheels were made of magnesium alloys. Although they lost favor on common vehicles, they remained popular through the 1960s, albeit in very limited numbers. In the mid-to-late 1960s, aluminum-casting refinements allowed the manufacture of safer wheels that were not as brittle. Until this time, most aluminum wheels suffered from low ductility, usually ranging from 2-3% elongation. Because light-alloy wheels at the time were often made of magnesium (often referred to as “mags”), these early wheel failures were later attributed to magnesium’s low ductility, when in many instances these wheels were poorly cast aluminum alloy wheels. Once these aluminum castingimprovements were more widely adopted, the aluminum wheel took the place of magnesium as low cost, high-performance wheels for motorsports.

Alloy wheel on a passenger car

Characteristics

Alcoa‘s heavy-duty alloy wheel, for buses and trucks.

Lighter wheels can improve handling by reducing unsprung mass, allowing suspension to follow the terrain more closely and thus improve grip, however not all alloy wheels are lighter than their steel equivalents. Reduction in overall vehicle mass can also help to reduce fuel consumption.

Better heat conduction[dubious ] and a more open wheel design can help dissipate heat from the brakes, which improves braking performance in more demanding driving conditions and reduces the chance of diminished brake performance or even failure due to overheating.

An aluminum alloy wheel designed to recall the crossed spokes of a wire wheel

Alloy wheels are also purchased for cosmetic purposes although the cheaper alloys used are usually not corrosion-resistant. Alloys allow the use of attractive bare-metal finishes, but these need to be sealed with paint or wheel covers. Even if so protected the wheels in use will eventually start to corrode after 3 to 5 years but refurbishment is now widely available at a cost. The manufacturing processes also allow intricate, bold designs. In contrast, steel wheels are usually pressed from sheet metal, and then welded together (often leaving unsightly bumps) and must be painted to avoid corrosion and/or hidden with wheel covers/hub caps.

Alloy wheels are prone to galvanic corrosion, which can cause the tires to leak air if appropriate preventive measures are not taken. Also, alloy wheels are more difficult to repair than steel wheels when bent, but their higher price usually makes repairs cheaper than replacement.

Chrysler alloy wheel

Alloy wheels are more expensive to produce than standard steel wheels, and thus are often not included as standard equipment, instead being marketed as optional add-ons or as part of a more expensive trim package. However, alloy wheels have become considerably more common since 2000 , now being offered on economy and subcompact cars, compared to a decade earlier where alloy wheels were often not factory options on inexpensive vehicles. Alloy wheels have long been included as standard equipment on higher-priced luxury or sports cars, with larger-sized or “exclusive” alloy wheels being options. The high cost of alloy wheels makes them attractive to thieves; to counter this, automakers and dealers often use locking lug nuts which require a special key to remove.

Most alloy wheels are manufactured using casting, but some are forged. Forged wheels are usually lighter, stronger, but much more expensive than cast wheels. There are two types of forged wheels: one piece and modular. Modular forged wheels may feature two- or three-piece design. Typical multi-piece wheels consist of the inner rim base, outer rim lip and wheel center piece with openings for lug nuts. All parts of a modular wheel are held with bolts. BBS RS is one of the most famous three-piece modular forged wheels.[1]

Aftermarket wheels

A sizable selection of alloy wheels are available to automobile owners who want lighter, more visually appealing, rarer, and/or larger wheels on their cars. Although replacing standard steel wheel and tire combinations with lighter alloy wheels and potentially lower profile tyres can result in increased performance and handling, this doesn’t necessarily hold when increasingly large wheels are employed. Research by Car and Driver conducted using a selection of differently sized alloy wheels from 16 to 19 in (41 to 48 cm) all outfitted with the same make and model of tires showed that both acceleration and fuel economy suffered with larger wheels.[2] They also noted that ride comfort and noise were negatively affected by the larger wheels.

Aftermarket brands

Most aftermarket wheels are cast, while only a few above are forged, such as Donz, Vellano and Weld.  Many companies have been formed over the years (some recently) due to the rising demand for larger diameter wheels. The demand for larger wheels was spurred on by the invention of wheel spinners by American Tru-Spinners. The original U.S. patent #5,290,094 that was invented by the founder of American Tru-Spinners James JD Gragg that licensed several wheel manufacturers and manufactured their own series of spinner wheels that were one-piece integral spinner wheels and some adaptable spinner wheels to where the center of the wheel continues spinning after the vehicle comes to a stop. American Tru-Spinners also invented another series of wheel spinners that spun backwards while the wheel traveled forwards and some traveled in a stationary position focusing on the wheel manufacturer logo staying level while in motion utilizing specialized bearings. American Tru-Spinners also introduced the use of Holograms in the spinner wheels that gave a lighted strobe effect without the use of a battery or electric source.

American Racing, which owns Motegi Racing among other brands such as TIS, TIS Modular, is the oldest aftermarket wheel company dating back to 1956. The oldest British company is Wolfrace which was the first company to offer a polished alloy wheel in Europe and to achieve TÜV approval. Wolfrace also provided the wheels for Thrust SSC and the UK’s land speed record bid. A recent trend in the industry includes joint venture partnerships being formed between offshore manufacturers and local importers/distributors such as PDW Wheels which started in Australia in 2006, amongst a few others.

Some “aftermarket” are/were also available as original equipment manufacturer (OEM) fitments, with BBS being a notable original equipment supplier to Volkswagen.

Some manufacturers also share patterns and castings, with an example (motorcycle) being the licensing of Marchesini five-spoke design to Brembo, for the production of alloy (non-magnesium) wheels for Ducati road bikes.

Magnesium alloy wheels

Magnesium alloy wheel on a Porsche Carrera GT

Magnesium alloy wheels were the first die-cast wheels produced, and were often referred to as simply “mag wheels.” Magnesium wheels were originally used for racing, but their popularity during the 1960s led to the development of other die-cast wheels, particularly of aluminum alloys. The term “mag wheels” became synonymous with die-cast wheels made from any material, from modern aluminum alloy wheels to plastic and composite wheels used on items like bicycles, wheelchairs, and skateboards.[3][4]

However, pure magnesium wheels are no longer produced, being found only on classic cars. Pure magnesium suffers from many problems. Vintage magnesium rims were very susceptible to pitting, cracking and corrosion. Magnesium in bulk is hard to ignite but pure magnesium wheels can be ignited by a burning tire or by prolonged scraping of the wheel on the road surface following a puncture. Alloys of magnesiumwere later developed to alleviate most of these problems.[5] In fact, US Federal Aviation Administration has conducted wide-ranging tests over the past decade, and has reached a conclusion that potential flammability of magnesium is no longer deemed to be a concern.[6]Modern surface treatment technologies provide protection from corrosion and significantly extend the average lifecycle of magnesium rims.

The mass of a typical magnesium automotive wheel is about 5–9 kg (11–20 lb) (depending on size).[7]

Production Methods

Forging

Forging can be done by a one or multi-step process forging from various magnesium alloys, most commonly AZ80, ZK60 (MA14 in Russia). Wheels produced by this method are usually of higher toughness and ductility than aluminum wheels, although the costs are much higher.[8]

High pressure die casting (HPDC)

This process uses a die arranged in a large machine that has high closing force to clamp the die closed. The molten magnesium is poured into a filler tube called a shot sleeve. A piston pushes the metal into the die with high speed and pressure, the magnesium solidifies and the die is opened and the wheel is released. Wheels produced by this method can offer reductions in price and improvements in corrosion resistance but they are less ductile and of lower strength due to the nature of HPDC.

Low pressure Die casting (LPDC)

This process usually employs a steel die, it is arranged above the crucible filled with molten magnesium. Most commonly the crucible is sealed against the die and pressurized air/cover gas mix is used to force the molten metal up a straw-like filler tube into the die.

Gravity cast alloy bicycle wheel. 1960s Bootie Folding Cycle

When processed using best practice methods LPDC wheels can offer improvements in ductility over HPDC magnesium wheels and any cast aluminum wheels, they remain less ductile than forged magnesium.

Gravity casting

Gravity-cast magnesium wheels have been in production since the early 1920s and provide good ductility, and relative properties above what can be made with aluminum casting. Tooling costs for gravity-cast wheels are among the cheapest of any process. This has allowed small batch production, flexibility in design and short development time.

References

  1. Brad Bowling (27 Feb 2004). Complete Wheel and Tire Buyer’s Guide. KP Books. p. 95. ISBN 978-0873496612.
  2. “Effects of Upsized Wheels and Tires Tested – Tech Dept. – Auto Reviews”. Car and Driver. Retrieved 2011-08-08.
  3. The ultimate hot rod dictionary: a-bombs to zoomies By Jeff Breitenstein, Troy Paiva – MBI Publishing 2004 Page 130
  4. The biomedical engineering handbook By Joseph D. Bronzino – CRC Press 2000 Page 141-4
  5. Automotive Detailing: A Complete Car Care Guide for Auto Enthusiasts and Detailing Professionals By Don Taylor – HP Books 1998 Page 72
  6. “Evaluating the Flammability of Various Magnesium Alloys During Laboratory- and Full-Scale Aircraft Fire Tests” (PDF). Federal Aviation Administration.
  7. “Wheelweights.Net”. Wheelweights.Net. Archived from the original on 24 July 2011. Retrieved 2011-08-08.
  8. https://f1wheels.com
Wheel A wheel is a circular component that is intended to rotate on an axle bearing. The wheel is one of the key components of the wheel and axle which is one of the six simple machines. Wheels, in conjunction with axles, allow heavy objects to be moved easily facilitating movement or transportation while supporting a load, or performing labor in machines. Wheels are also used for other purposes, such as a ship's wheel, steering wheel, potter's wheel and flywheel. Common examples are found in transport applications. A wheel greatly reduces friction by facilitating motion by rolling together with the use of axles. In order for wheels to rotate, a moment needs to be applied to the wheel about its axis, either by way of gravity or by the application of another external force or torque. Using the wheel, Sumerians invented a contraption that spins clay as a potter shapes it into the desired object. Three wheels on an antique tricycle The earliest wheels were m...
Rim (wheel) The rim is the "outer edge of a wheel, holding the tire". It makes up the outer circular design of the wheel on which the inside edge of the tire is mounted on vehicles such as automobiles. For example, on a bicycle wheel the rim is a large hoop attached to the outer ends of the spokes of the wheel that holds the tire and tube. The term rim is also used non-technically to refer to the entire wheel, or even to a tire. In the 1st millennium BC, an iron rim was introduced around the wooden wheels of chariots. Cross section of a bicycle rim wooden bicycle rim with tubular tyre Characteristics Scratched rim on two-piece wheel. Black residue remaining from where the tire was seated on the "safety profile" rim. Diameter (effective): distance between the bead seats (for the tire), as measured in the plane of the rim and through the axis of the hub which is or will be attached, or which is integral with the rim. Width (e...
Tweel The Tweel (a portmanteau of tire and wheel) is an airless tire design concept developed by the French tire company Michelin. Its significant advantage over pneumatic tires is that the Tweel does not use a bladder full of compressed air, and therefore it cannot burst, leak pressure, or become flat. Instead, the Tweel assembly's inner hub connects to flexible polyurethane spokes which are used to support an outer rim and these engineered compliant components assume the shock-absorbing role provided by the compressed air in a traditional tire. The Tweel airless tire design Design The Tweel consists of a band of conventional tire rubber with molded tread, a shear beam just below the tread that creates a compliant contact patch, a series of energy-absorbing polyurethane spokes, and an integral inner rim structure. Both the shear beam and the polyurethane spokes can be designed to provide a calibrated directional stiffness in order that design engineers are able to control both how th...
Wire wheel Wire wheels, wire-spoked wheels, tension-spoked wheels, or "suspension" wheels are wheels whose rims connect to their hubs by wire spokes. Although these wires are generally stiffer than a typical wire rope, they function mechanically the same as tensioned flexible wires, keeping the rim true while supporting applied loads. The term suspension wheel should not be confused with vehicle suspension. Wire wheels are used on most bicycles and are still used on many motorcycles. They were invented by aeronautical engineer George Cayley in 1808. Although Cayley first proposed wire wheels, he did not apply for a patent. The first patent for wire wheels was issued to Theodore Jones of London, England on October 11, 1826. Eugène Meyer of Paris, France was the first person to receive, in 1869, a patent for wire wheels on bicycles. Bicycle wheels were not strong enough for cars until the development of tangentially spoked wheels. They rapidly became well established in the bicycle and motor ...
Artillery wheel The artillery wheel was developed for use on gun carriages when it was found that the lateral forces involved in horse artillery manoeuvres caused normally constructed cart wheels to collapse. Rather than having its spokes mortised into a wooden nave (hub), it has them fitted together (mitred) then bolted into a metal nave. Its tyre is shrunk onto the rim in the usual way but it is also bolted on for security. A normal wagon wheel is dished so that in its lowest part, the spokes are perpendicular to the ground thus supporting the weight (with the axle not truly horizontal but angled downward toward the outside about 5 degrees). This is not done with artillery wheels.    Artillery wheel Motor vehicles 1927 Ford T with artillery wheels When higher speeds and consequently higher lateral forces were attained with the introduction of motor vehicles, the artillery wheel was used in those too. By the 1920s, motor cars used wheels that looked at a glance...