Direct TPMS

Direct TPMS, or direct tire pressure monitoring systems (direct sensor TPMS) refers to the use of a pressure sensor directly mounted on the wheels or tires of a vehicle.[1] The pressure inside the tire is measured using a pressure transducer with the pressure information being subsequently sent to the vehicle to warn the driver of under or over inflation of a tire. The pressure information is commonly transmitted to the vehicle using radio frequency (RF) technology, though systems using mechanical, electrical or magnetic methods have been used over recent years.[2]

Typical system

direct TPM sensor fitted in valve system, manufacturer VDO

In most current designs of direct TPMS, a small electronic assembly which is rugged enough to be mounted inside a tire, measures the pressure using a microelectromechanical system (MEMS)[1] pressure sensor and then transmits this and other information to one or more vehicle receivers.[1] Other information can include a serial number, temperature, acceleration and the status of the complete tire pressure monitoring system.[3] The purpose of the serial number is to allow the vehicle to ignore transmissions from other vehicles and operate with a unique data field. A typical direct TPMS (e.g. Ford,[4] BMW[5] or Toyota[6]) comprises the following components on a vehicle:

  • A direct TPM sensor fitted to the back of the valve stem on each wheel
  • A TPM Warning Light
  • Unique identifier (ID’s) for which tire is providing the data including speed and the direction of rotation
  • A tire pressure monitor electronic control unit (ECU)
  • Antenna(s)
  • Controller for periodic measurements
  • Source of power
  • Diagnostics and wake up system

Most direct TPMS systems use ultra high frequency (UHF) radio in one of the ‘unlicensed’ ISM bands (industrial, scientific and medical) for transmitting the data,[7] often around 434 MHz in Europe and 315 MHz in much of the rest of the world. On some systems there is a separate receiver or antenna near each wheel whilst more commonly there is a single receiver which receives data from all of the wheels on the vehicle. Commonly this receiver is also used for remote keyless entry system (RKE) as this also usually uses UHF radio transmissions.

TPM sensors can be fitted to the wheels in a number of ways. They can be mounted on the back of the tire’s valve stem[8] or attached using adhesive or to a band which is then securely wrapped around the rim inside the tire, usually in the drop zone.[9]

Direct tire pressure monitor system warning light

When the direct TPMS warning light comes on, either one of the tires is under-inflated, severely over-inflated, or there is a fault with the system.[1] If the light is constant then inflating to the correct placard pressure should turn it off. If this is not the case then this indicates a puncture. If the light is intermittent or if it stays on after correct inflation or replacement of a punctured tire then this indicates a fault with the direct TPMS system.[1]

Registration of direct TPMS IDs

When the direct TPMS system is fitted at the factory the unique ID numbers of the TPM (tire pressure monitoring) sensors have to be registered along with their position on the vehicle with the tire pressure monitor ECU. This is also the case if any of the system components are subsequently changed e.g. in the event of rotating the tires, changing sensors, replacing the ECU etc.[4]

This process requires the activation of the direct TPMS sensor using low frequency (LF) radio and the capture of the UHF data transmitted. This data includes the direct TPMS ID, the pressure and the temperature. In automotive manufacturing plants, the activation is carried out using large antenna systems whilst in the dealerships and tire shops, hand tools are used. These tools can also be used to check the direct TPMS for faults prior to disassembly. If a TPM sensor or its position on the car are changed without re-registering the IDs, then the TPMS warning light will turn on and stay on until the IDs are re-registered.[1]

Localisation

If there are multiple antennas or receivers, this permits localisation of the TPM such that the vehicle can tell from which wheel the pressure data has come. As an alternative to this method, the vehicle can be programmed at the time of manufacture with the position of the tire together with its TPM serial number. This allows the vehicle to display which tire has low pressure.[10]

Also, some vehicles have low frequency radio transmitters mounted near to each wheel which can be used to force the individual TPMs to transmit at will. These typically use similar technology to 125 kHz RFID tags where the transmitted field is predominantly magnetic and can be easily detected by a small LF antenna located in the TPM. This method of localisation is often referred to as a high line system.

The LF antenna is also often used by the TPM for configuration and to force transmission so that localisation can be re-learned by the vehicle if a sensor is changed or the wheels rotated to even up tread wear.

A third method uses the UHF signal strength which is proportional to the distance of the TPM from the receiver. If the receiver is located towards the front of the vehicle, the signal from the front wheel TPM’s will be stronger than that from the wheels at the rear.

The TPM also has a method of detecting the rotational direction of each wheel to identify which side of the vehicle the TPM is located and this information forms part of the message transmitted to the vehicle. This combination allows the correct wheel to be identified.

TPM sensor features

The TPM sensors currently fitted to high volume production cars worldwide are battery-powered, self-contained units which periodically measure tire pressure, and often temperature and acceleration. The sensor is equipped with an RF transmitter circuit which is used to broadcast the measured pressure etc. within the tire.[11]

The TPM is designed to use as little power as possible to give maximum battery life. This is done by using very low power circuitry and transmitting the data as infrequently as possible and with as low power as possible. The UHF transmitter in a TPM typically transmits around 250μW (1μW is equal to one millionth (10−6) of a watt).

TPMs do not have UHF receivers built in due to the relatively high power requirements of this technology. This means that they can’t tell that they are transmitting at the same time as another TPM. Most TPMs do have LF receivers as this uses little or no power.

The pressure, temperature and acceleration sensors generate analog signals which are converted to their digital equivalents using analog to digital converters. The acceleration sensor measures the centrifugal force generated when the wheel rotates. This force is proportional to the rotational speed. The acceleration sensor may be a simple switch rather than an analog transducer (accelerometer). This is usually referred to as a roll switch. The acceleration sensor allows the TPM to be placed in a low-power communication devicemode, when the vehicle is stationary which can extend the battery life. The advantage of a roll switch over an accelerometer is that the switch is purely mechanical and doesn’t use any power to take a measurement.[12]

When the vehicle is stationary, the TPM may periodically transmit to the vehicle. This allows (as long as the vehicle receiver is always on) the driver or vehicle operator to be warned of low pressure as soon as the Ignition system is switched on rather than having to wait until the vehicle is moving.

All TPM units on a vehicle operate on the same RF channel frequency and each message includes pressure data, temperature data, a unique ID code, operating state data, status information and check digits. The check digit is either a checksum or a cyclic redundancy check (CRC).

The TPM does not usually have information about the tire’s correct pressure as this would be very difficult and possibly dangerous to support. However it may have an algorithmcontained within it which detects both slow and rapid changes in pressure. This condition may be transmitted as part of the TPM’s status. It may also cause the TPM to transmit more frequently.

Direct tire pressure monitoring systems

There are two main types of direct tire pressure monitoring system currently in use. These are known as ‘high line’ and ‘low line’.[13]

High line system

If the vehicle is fitted with low frequency (LF) transmitters near each wheel, the vehicle may use these to force the sensors to transmit. In this case, the TPM may not transmit on its own, but the vehicle will periodically command the sensors to send their information.[14]

In addition, the TPMs will be forced to transmit when the ignition is switched on. This will give an early indication of low pressure without having to have the vehicle’s receiver switched on when the vehicle is not in use. The transmitters are usually activated one at a time in sequence so that the vehicle can inform the driver of the location of the wheel with low pressure. This information can then be used later for localisation by matching the TPM’s unique ID with its position discovered by this sequential activation. This method is used on some high line systems where the TPM also transmits periodically.

On some vehicles only three LF transmitters are used in order to save money. The vehicle assumes that transmissions from a nearby TPM which has not been woken up by the LF belong to the TPM located where there is no LF transmitter.

High line systems are inherently more expensive than low line systems but they have the advantage of the vehicle knowing the pressure when started without draining the vehicle’s main battery and providing localisation. These systems tend to be used on higher end models.

Low line system

In this system, the TPM units transmit on their own at fixed or random intervals. As the individual TPMs on the vehicle do not know if another TPM is transmitting at the same time, it is possible to have collisions between messages transmitted. Measures have to be taken to ensure that the message is received by the vehicle. On some systems the message is re-transmitted multiple times to reduce the effect of interference (communication). The transmission pattern can be random or pseudo random to reduce the chance of collisions between transmissions from the sensors on the vehicle.[14]

Another method of attempting to avoid collisions is simply to transmit more frequently such as once per minute. In addition, if the TPM detects a rapid change in pressure or too high a temperature, it will start to transmit more frequently so that the vehicle has more chance of receiving the information. The low line system is used on the majority of vehicles due to its lower cost.

Legal status

USA

The use of TPMS in vehicles in the USA was mandated in 2008 by the Transportation Recall Enhancement, Accountability and Documentation Act (or TREAD). This states that the driver of a vehicle must be warned of under inflation by 25%.[15] The warning is displayed to the driver in line with 49 CFR Part 571 Federal Motor Vehicle Safety Standards (FMVSS). The minimum requirement for the warning is in the form of a simple lit symbol on the dashboard, and this is often augmented by the display of a graphic of the car showing the wheel position to which the warning light corresponds. All new model year 2008 light vehicles shall have a TPMS (direct or indirect) fitted which is capable of detecting when one or more of the vehicle’s tires, up to all four tires, is 25% or more below the manufacturer’s recommended inflation pressure (placard pressure) or a minimum activation pressure specified in the standard, whichever is higher.[16]

EU and Far East

European Union (EU) and Far East legislators are looking at TPMS as a way of reducing CO2 emissions, and are presently (as at January 2009) considering compulsory tire pressure monitoring systems from this environmental stance.[17] Starting in November 2014 (ECE-R 64 EU Directive), all new models of passenger cars must be equipped, in E.U., with a TPMS.

Notes

  1.  b c d e f Hawes, p. 1.
  2.  Hawes, p. 2.
  3.  Hawes, p. 123.
  4.  b Hawes, p. 185.
  5.  Hawes, p. 51.
  6.  Hawes, p. 690.
  7.  http://www.itu.int/ITU-R/terrestrial/faq/index.html
  8.  Hawes, p. 3.
  9.  Hawes, p. 459.
  10.  http://www.wipo.int/pctdb/en/wo.jsp?wo=2006104484&IA=WO2006104484&DISPLAY=DESC
  11.  http://www.freescale.com/webapp/sps/site/overview.jsp?nodeId=02Wcbf123F2D5D
  12. http://www.yole.fr/pagesAn/products/Report_sample/TPMS_tire_pressure_system_market_report.pdf
  13.  Hawes, p. 361.
  14.  b Hawes, p. 363.
  15. http://www.nhtsa.dot.gov/staticfiles/DOT/NHTSA/Rulemaking/Rules/Associated%20Files/TPMS-2005-FMVSS-No138.pdf
  16.  http://www.nhtsa.dot.gov/cars/rules/rulings/tirepresfinal/index.html
  17.  http://www.iea.org/Textbase/work/2005/EnerEffTyre/stock.pdf
Tire code Automobile tires are described by an alphanumeric tire code (in American English and Canadian English) or tyre code (in British English, Australian English and others), which is generally molded (or moulded) into the sidewall of the tire. This code specifies the dimensions of the tire, and some of its key limitations, such as load-bearing ability, and maximum speed. Sometimes the inner sidewall contains information not included on the outer sidewall, and vice versa. The code has grown in complexity over the years, as is evident from the mix of SI and imperial units, and ad-hoc extensions to lettering and numbering schemes. New automotive tires frequently have ratings for traction, treadwear, and temperature resistance (collectively known as The Uniform Tire Quality Grade (UTQG) ratings). Most tires sizes are given using the ISO Metric sizing system. However, some pickup trucks and SUVs use the Light Truck Numeric or Light Truck High Flotation system. National technical standards...
Tire-pressure monitoring system A tire-pressure monitoring system (TPMS) is an electronic system designed to monitor the air pressure inside the pneumatic tires on various types of vehicles. TPMS report real-time tire-pressure information to the driver of the vehicle, either via a gauge, a pictogram display, or a simple low-pressure warning light. TPMS can be divided into two different types – direct (dTPMS) and indirect (iTPMS). TPMS are provided both at an OEM (factory) level as well as an aftermarket solution. The target of a TPMS is avoiding traffic accidents, poor fuel economy, and increased tire wear due to under-inflated tires through early recognition of a hazardous state of the tires. History Initial adoption Due to the influence tire pressure has on vehicle safety and efficiency, tire-pressure monitoring (TPM) was first adopted by the European market as an optional feature for luxurypassenger vehicles in the 1980s. The first passenger vehicle to adopt TPM was the Porsche 959 in 1986, using a hollow spoke...
Tire A tire (American English) or tyre (British English; see spelling differences) is a ring-shaped component that surrounds a wheel's rim to transfer a vehicle's load from the axle through the wheel to the ground and to provide traction on the surface traveled over. Most tires, such as those for automobiles and bicycles, are pneumatically inflated structures, which also provide a flexible cushion that absorbs shock as the tire rolls over rough features on the surface. Tires provide a footprint that is designed to match the weight of the vehicle with the bearing strength of the surface that it rolls over by providing a bearing pressure that will not deform the surface excessively. The materials of modern pneumatic tires are synthetic rubber, natural rubber, fabric and wire, along with carbon black and other chemical compounds. They consist of a tread and a body. The tread provides traction while the body provides containment for a quantity of compressed air. Before rubber was developed, ...
Snow tire Snow tires—also called winter tires—are tires designed for use on snow and ice. Snow tires have a tread design with bigger gaps than those on summer tires, increasing traction on snow and ice. Such tires that have passed a specific winter traction performance test are entitled to display a "Three-Peak Mountain Snow Flake" symbol on their sidewalls. Tires designed for winter conditions are optimized to drive at temperatures below 7 °C (45 °F). Some snow tires have metal or ceramic studs that protrude from the tire to increase traction on hard-packed snow or ice. Studs abrade dry pavement, causing dust and creating wear in the wheel path. Regulations that require the use of snow tires or permit the use of studs vary by country in Asia and Europe, and by state or province in North America. Related to snow tires are those with an M+S rating, which denotes an "all-season" capability—quieter on clear roads, but less capable on snow or ice than a winter tire. Winter tire, showing tr...
Tread The tread of a tire or track refers to the rubber on its circumference that makes contact with the road or the ground. As tires are used, the tread is worn off, limiting its effectiveness in providing traction. A worn tire can often be retreaded. The word tread is often used casually to refer to the pattern of grooves molded into the rubber, but those grooves are correctly called the tread pattern, or simply the pattern. The grooves are not the tread, they are in the tread. This distinction is especially significant in the case of racing slicks, which have a lot of tread but no grooves. Tires Common tire tread pattern. Street tires The grooves in the rubber are designed to allow water to be expelled from beneath the tire and prevent hydroplaning. The proportion of rubber to air space on the road surface directly affects its traction. Design of tire tread has an effect upon noise generated, especially at freeway speeds. Generally there is a tradeoff of tre...